Hydro-jetting is a drain and sewer cleaning method that uses water at 3,500 to 4,000 PSI delivered through a specialized nozzle to scour the full interior of a pipe, removing grease, scale, mineral buildup, and roots that a cable cannot.
A cable opens a channel through the clog. Jetting cleans the pipe. The difference matters when the same drain keeps backing up every six months, or when the cause is something a cable just punches through and leaves behind. For older Orlando homes with cast iron drainage scaling shut from the inside, or vacation rentals near the parks with grease loading the kitchen line, jetting is usually the right tool. We size the rig to the line, choose the right nozzle for the buildup, and run a camera before and after so you can see the work.
Two things drive jetting demand in Orlando. The first is cast iron. A lot of housing stock built between 1955 and 1985 used cast iron for drainage, and after 40-plus years the inside of a 3-inch line can be down to an inch of clear flow because of scaling and corrosion. A cable bores through and the drain works for a month before clogging again. Jetting actually removes the scale from the pipe wall. The second is grease. Vacation rental kitchens get hammered by short-stay guests who pour bacon grease and pasta water down the drain, and the kitchen branch line loads with hardened grease within a year of being snaked. Jetting cuts the grease back to bare pipe.
Grease cools, hardens, and sticks to whatever it touches inside the pipe. Once a layer builds up it traps everything else that goes by. Coffee grounds, food bits, soap residue. And the pipe diameter shrinks. A cable knocks a hole through the grease and it closes again within weeks. Jetting with a grease-cutting nozzle scours the wall back to clean pipe.
Live oak and ficus roots will find any moisture in your lateral and they push into the joints of clay or cast iron pipe. A root-cutting jetter nozzle has rear and forward jets that slice and flush the roots out as the line is cleaned. The roots grow back through the same cracked joint within a year or two, so jetting buys time while you decide on a long-term repair like lining or pipe bursting.
Cast iron pipe corrodes from the inside out. The corrosion sheds into the flow as scale and the wall gets bumpy, which slows everything down. A descaling chain nozzle on the jetter knocks the scale off and the pipe gets close to its original diameter back. Jetting alone won't replace structurally bad pipe but it can extend the life of marginal pipe and is often the right call before a CIPP lining.
Restaurants, food trucks, hotels, and assisted living facilities all run kitchen waste through 3-to-4-inch lines that need scheduled jetting to prevent backups. We work with property managers in the I-Drive and Sand Lake corridors to schedule quarterly or semi-annual cleanings before grease causes a midweek shutdown.
| Cable / auger | Hydro-jetting | |
|---|---|---|
| What it does | Opens a channel through the blockage | Scours the full pipe wall clean |
| Grease | Punches through, returns fast | Removes back to bare pipe |
| Roots | Cuts a hole through them | Cuts and flushes out of the line |
| Scale | Doesn't address it | Knocks scale off the wall |
| Pipe diameter | Restored at the clog only | Restored across the cleaned section |
| Relative cost | $ | $$ |
| Job | Typical range |
|---|---|
| Residential branch line jetting | $295–$550 |
| Main sewer line jetting (40–75 ft) | $395–$800 |
| Commercial kitchen line jetting | $450–$1,100 |
| Camera inspection before / after | $125–$350 |
Ballpark Orlando-area ranges. Your exact price depends on the job, and we give a firm, free quote before any work starts.
FBC-P 707 and FBC-P 1003 govern the drains being cleaned. Residential hydro-jetting in Orlando does not require a permit when no fixtures are altered, but a camera inspection report is best practice before and after jetting on lines older than 30 years to document condition.
Residential hydro-jetting runs $400 to $900 in the Orlando metro for 2026, with $575 as the typical median for a 4-inch lateral cleaned end-to-end. Commercial lines (4-6 inch) run $800 to $1,800. Adding a camera inspection adds $200 to $400.
A typical residential job takes 90 to 150 minutes including setup, jetting both directions from the cleanout, and a camera verification pass. We schedule same-day for non-emergency jetting in 80% of metro calls.
Our equipment includes US Jetting 4018 and 4030 trailer units (4000 PSI, 18-30 GPM), Spartan Warrior portable jetters (1500 PSI for residential interior), Sewer Equipment Co. JM-3000 trailer, and RIDGID KJ-3100 cart-mount for tight residential access.
Older drain infrastructure concentrates jetting demand: 32801, 32803, 32805, 32806, and 32812 in Orlando proper, plus 32789 (Winter Park) and 32771 (Sanford). Tree-root jetting work clusters in 32839 and 32792.
If snaking only works for a few weeks, jetting is usually what the line actually needs. Call (407) 964-8940 for a camera-first quote. We look before we work and tell you straight whether jetting is the right call.
Jetting is often the prep step for sewer line repair or CIPP lining. It also pairs with routine drain cleaning for branches that don't need the high-pressure treatment. Older homes in College Park and Conway see this work most often.
It depends on the pipe. Modern PVC and clean copper handle it without issue. Old galvanized supply, badly corroded cast iron, or cracked clay laterals need a careful read before jetting. We camera first and pick the right PSI and nozzle for the material. If the pipe is too far gone we recommend repair instead of jetting.
A branch line takes 30 to 60 minutes including the camera check before and after. A main sewer line jetting with camera work runs 90 minutes to 2 hours. Commercial kitchen lines depend on the length and the grease load.
No. Jetting cleans the line. If the underlying problem is a cracked joint, a belly, or roots growing through a structural defect, the buildup comes back and you need a structural repair. The camera tells the difference. We use jetting as part of the diagnosis and as the right answer when the pipe itself is sound.
Lower-PSI jetters are designed for branch lines and grease. Higher-PSI commercial-grade rigs handle main sewers, roots, and heavy scale. Matching the rig to the line is part of the job. Too little pressure does nothing, too much can stress thin pipe walls.
Healthy pipe in good condition, no. We adjust PSI to the pipe material and run a camera first to check the structural condition. The only real risk is on already-failing pipe, where jetting can sometimes accelerate a failure that was coming anyway. In those cases we recommend repair before cleaning.
Quarterly is standard for high-volume restaurants and ghost kitchens. Semi-annual works for moderate-volume operations. Most code-cited backup events trace back to lines that have not been cleaned for a year or more.
It cuts and flushes the roots out of the line, but the roots will grow back through the same cracked joint over time. Jetting buys 12 to 24 months on most root jobs. The permanent fix is to seal the joint, usually with a CIPP liner or by replacing that section of pipe.
On main sewer lines, yes. Always. The camera tells us pipe material, condition, and where the problem actually is. On branch lines for a known clog we sometimes go straight to the jetter and camera after. We tell you upfront which we recommend for your job.
Residential branch jetting runs $295 to $550, main sewer jetting $395 to $800, and commercial kitchen jetting $450 to $1,100. Camera work runs $125 to $350. We give you a firm number on-site before any work starts.
Our team is available around the clock to better assist you. Call now for fast, friendly help.
We work across eight regions of Greater Orlando. Reasons the service matters change by neighborhood, county, and home era.
Older Orlando neighborhoods have cast-iron drainage that scales shut from the inside. College Park, Thornton Park, and Delaney Park are top jetting candidates for descaling cast iron and clearing roots from clay laterals.
Downtown Orlando, Thornton Park, College Park, Audubon Park, Baldwin Park, Delaney Park, Parramore, and Fairview Shores
Conway and Belle Isle 1960s-80s homes with original cast iron benefit from periodic descaling jetting. Lake Nona and newer south-side communities rarely need jetting because PVC drainage doesn't scale.
Lake Nona, Waterford Lakes, Avalon Park, Alafaya, Azalea Park, Rio Pinar, Union Park, Conway, Belle Isle, Pine Castle, Sky Lake, Hunters Creek, Meadow Woods, Williamsburg, and Lake Buena Vista
Doctor Phillips Restaurant Row commercial kitchens are quarterly jetting customers. Grease loads on 4-inch lines need scheduled cleaning to prevent backups. Pine Hills slab homes have cast-iron drainage that benefits from periodic descaling.
Pine Hills, MetroWest, Doctor Phillips, Windermere, and Goldenrod
Apopka and Winter Garden historic downtown businesses use jetting for grease-laden kitchen lines. Older homes in these towns carry cast-iron drainage that scales over decades.
Apopka, Maitland, Winter Park, Ocoee, Winter Garden, Oakland, Gotha, Zellwood, Clarcona, Bithlo, Wedgefield, and Christmas
Sanford's historic restaurants along Park Avenue and downtown homes both benefit from jetting. Grease for the commercial, scale for residential. Lake Mary and Heathrow newer-build subdivisions rarely need jetting.
Sanford, Lake Mary, Heathrow, Longwood, Altamonte Springs, Casselberry, Fern Park, Forest City, Wekiwa Springs, Winter Springs, Oviedo, Geneva, and Lake Monroe (community)
DeLand's downtown commercial corridor and historic district homes have aging cast-iron drainage and the oldest sewer service in Volusia. Deltona's 1960s-80s tract homes are descaling candidates.
DeBary, Deltona, Orange City, Enterprise, Osteen, DeLand, and Cassadaga
Eustis, Tavares, and Mount Dora downtown commercial properties use jetting on kitchen and restaurant lines. Historic-district homes in all three benefit from periodic descaling.
Eustis, Tavares, Mount Dora, Sorrento, Montverde, and Clermont
Vacation rental and short-term rental kitchens in Davenport, Reunion, Celebration, and Kissimmee see heavy grease loads from rotating guests. Quarterly or semi-annual jetting on kitchen branch lines prevents the turn-day surprise.
Kissimmee, Saint Cloud, Buenaventura Lakes, Poinciana, Intercession City, Davenport, Four Corners, Reunion, and Celebration
A few of the communities we serve. View all →
We provide hydro jetting across 75 cities and neighborhoods in Greater Orlando. Click your city for local detail, pricing, and what we typically see there.